How to Connect the Battery Cable?

How to Connect the Battery Cable?

      Charging the car battery is a recommended process in auto services. However, in some cases, the battery may run out prematurely. At such moments, users will need to do the battery boosting process in the most accurate way. Even if it is done with simple operations, the slightest wrong operation can have negative consequences for the battery and your vehicle. If you have the new battery with you, you will need to replace your old battery with a new one. However, if the battery runs out while driving, there is a need to charge the battery from the car to the car. The question of how to make a battery supplement can be answered according to these different processes.

Considerations in Battery Cable Connection

If you are going to replace the dead battery with a new battery, start by removing your old battery. Before starting these processes, be sure to take your personal safety precautions. Because even if the battery is exhausted, it may contain electricity and combustion gases that are harmful to human health.

  • Take care to use protective glasses and current protective gloves during the procedures.
  • Make sure the vehicle is switched off with the ignition.
  • Always start battery removal from the negative (-) poles. After removing the battery cover, use the appropriate wrench to remove the negative terminal.
  • Then do the same for the positive (+) cap under the red cap.
  • You can try the key heads with the help of the extension arm to find the most suitable one for key selection. However, do them as a matter of sight, without touching the poles. After you find the suitable one, continue the process.
  • After loosening the terminals, remove them and place them away from the battery.
  • After the battery is disconnected, the screws of the brackets holding the battery in its compartment are also unscrewed.
  • It removes the idle battery properly without touching other components.
  • Since the battery stays in the car interior for many years, you can prepare a carbonate mixture diluted with water to clean the compartment after the battery is removed, and clean it with a soft-tipped toothbrush. Only insert the new battery after the battery compartment is dry.
  • You can repeat the same operations while inserting the new battery. First of all, place the battery properly in the bracket and tighten the connection screws. Make sure the battery is not playing.
  • Connect the positive (+) terminals first and then the negative (-) terminals.
  • Close the hood after making sure that nothing metal or watery remains on the battery. For the battery check, start your vehicle and check the starter test and the operation of other components.
  • You can give your old battery to your recycling points or auto service.

Battery Booster Tips

      How to connect car jumper cable? The question can be examined as before and after the procedure. First of all, if you have to make the connection, you need to know the color and characteristics of each battery jumper cable. Why is the battery cable important? If we say that, the battery provides all the energy that the vehicle needs. The battery is the basis of many functions such as cranking, radio, air conditioning and lighting systems. Battery cable ends must be connected carefully. While connecting the battery charging cable, care should be taken that it does not come into contact with other points. The cables must be installed in the right places and tightened well. Battery connection cables also differ in amperage. In the question of how many amps the battery cable should be, the answer will vary depending on whether your vehicle is a motorcycle, passenger vehicle or commercial bus. It also has a wide selection of battery types. Battery replacements are also preferred in accordance with this difference, and battery replacement procedures may also be different. If your vehicle is suitable for the start-stop battery, your new battery will also need to have this feature. One of the most important tricks after the battery replacement process is control. After correct and all necessary connections are made, the gas of the car should be pressed and it should be checked whether there is any problem.

Recommended Content: Battery Components

Battery Jumper Materials

      It has very solid contents as battery cable production. Years of use depend on the quality of these materials. If we first consider the question of what is the use of the battery jumper cable, it serves to transmit the energy in the battery to the components that the vehicle needs. At the stage of how to make a battery booster cable, we can take a look at the materials of the materials. It has multi-stranded tin-free copper wire with electrolytic conductive properties as material. The outside of this material is PVC insulated. Cable lengths and cross-sections vary according to the vehicle. We can see these as 2-5 meters in cable length and 16,25,35,50 and 70 mm2 in cable cross sections. All these differences also determine the battery prices. You can examine our web page to determine the suitable battery for your vehicle and to examine the varieties of Esan Akü, which is the leader of the sector with its products that do not deviate from its quality.

How Many Amps Should Battery Booster Cables Have?

       Whether it is a battery booster cable or battery value, it is preferred in every vehicle with its different features. The battery charger does not exceed 14.40 volts during operation. Battery booster cables must also be of a certain standard in terms of amperage. Well, we can examine the question of how many amps the battery booster cable should be, again according to the type of vehicle. They should have 300-600 amperes in motorcycles, 700-1200 amperes in passenger cars, 1200 amperes in light commercial vehicles and 1200-2400 amperes in large vehicles such as trucks and buses.

What Happens If The Cables Are Reversed?

       Care must be taken when connecting the battery jumper cable to the vehicle. If the battery connections are made incorrectly, not only the battery charging process will be interrupted, but the diodes will be damaged so that they will not work. The battery must be fully connected with the steps in the user manual. If the ignition is in working condition, it may even damage your vehicle. For such transactions, be sure to consult your auto service.

Share This Post